You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

126 lines
4.0 KiB

/* This source file is part of the ATMEL AVR-UC3-SoftwareFramework-1.7.0 Release */
/*! \page License
* Copyright (C) 2009, H&D Wireless AB All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
*
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* 3. The name of H&D Wireless AB may not be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY H&D WIRELESS AB ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY AND
* SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT,
* INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include <avr32/io.h>
#include "printf-stdarg.h"
#include "wl_fw.h"
#include "startup.h"
#include "nor_flash.h"
#include "gpio.h"
#define GREEN_OFF() gpio_set_gpio_pin(LED0_GPIO)
#define GREEN_ON() gpio_clr_gpio_pin(LED0_GPIO)
#define GREEN_BLINK() gpio_tgl_gpio_pin(LED0_GPIO)
#define RED_OFF() gpio_set_gpio_pin(LED1_GPIO)
#define RED_ON() gpio_clr_gpio_pin(LED1_GPIO)
#define RED_BLINK() gpio_tgl_gpio_pin(LED1_GPIO)
#define BLUE_OFF() gpio_set_gpio_pin(LED2_GPIO)
#define BLUE_ON() gpio_clr_gpio_pin(LED2_GPIO)
#define BLUE_BLINK() gpio_tgl_gpio_pin(LED2_GPIO)
/**
*
*/
void
led_init(void)
{
gpio_enable_gpio_pin(LED0_GPIO);
gpio_enable_gpio_pin(LED1_GPIO);
gpio_enable_gpio_pin(LED2_GPIO);
GREEN_OFF();
RED_OFF();
BLUE_OFF();
}
int main(void)
{
U32 pos, len;
startup_init();
printk("*** HD chip firmware upgrade ver 2.7 ***\n");
led_init();
flash_init();
GREEN_ON();
if (at45dbx_mem_check() == OK)
{
printk("Memory check... [ OK ]\n");
}
else
{
RED_ON();
GREEN_OFF();
printk("Memory check... [FAIL]\n");
return 0;
}
printk("Writing firmware data to flash\n");
pos = 0;
while (pos < fw_len) {
if (fw_len - pos > SECTOR_SIZE)
len = SECTOR_SIZE;
else
len = fw_len - pos;
flash_write(pos, fw_buf + pos, len);
pos += len;
}
printk("Verifying firmware data\n");
pos = 0;
while (pos < fw_len) {
static U8 page_buf[SECTOR_SIZE];
U32 i;
if (fw_len - pos > SECTOR_SIZE)
len = SECTOR_SIZE;
else
len = fw_len - pos;
flash_read(pos, page_buf, len);
for (i = 0; i < len; i++)
if (*(page_buf + i) != *(fw_buf + pos + i)) {
RED_ON();
GREEN_OFF();
printk("Verify failed at byte %d, 0x%02x != 0x%02x\n",
pos + i, *(page_buf + i), *(fw_buf + pos + i));
return 0;
}
pos += len;
}
GREEN_OFF();
BLUE_ON();
printk("Firmware successfully stored in flash!\n");
return 0;
}