mitchellhansen
/
battletank
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

remove wonky submodule

Browse Source
master
mitchellhansen 5 years ago
parent 5cb45ad648
commit f5cc389e53
5 changed files with 1994 additions and 1 deletions
Show Stats Download Patch File Download Diff File

1
arduino/libraries/RF24

@ -1 +0,0 @@
Subproject commit ebcd0d1d0b3061fcb57444e1dbe5829ef25705cd

985
arduino/libraries/RF24/RF24.cpp
Unescape View File

@ -0,0 +1,985 @@
/*
Copyright (C) 2011 J. Coliz <maniacbug@ymail.com>
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
version 2 as published by the Free Software Foundation.
*/
#include "nRF24L01.h"
#include "RF24_config.h"
#include "RF24.h"
#include <util/delay.h>
/****************************************************************************/
void RF24::csn(int mode)
{
// Minimum ideal SPI bus speed is 2x data rate
// If we assume 2Mbs data rate and 16Mhz clock, a
// divider of 4 is the minimum we want.
// CLK:BUS 8Mhz:2Mhz, 16Mhz:4Mhz, or 20Mhz:5Mhz
#ifdef ARDUINO
SPI.setBitOrder(MSBFIRST);
SPI.setDataMode(SPI_MODE0);
SPI.setClockDivider(SPI_CLOCK_DIV4);
#endif
digitalWrite(csn_pin,mode);
}
/****************************************************************************/
void RF24::ce(int level)
{
digitalWrite(ce_pin,level);
}
/****************************************************************************/
uint8_t RF24::read_register(uint8_t reg, uint8_t* buf, uint8_t len)
{
uint8_t status;
csn(LOW);
status = SPI.transfer( R_REGISTER | ( REGISTER_MASK & reg ) );
while ( len-- )
*buf++ = SPI.transfer(0xff);
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::read_register(uint8_t reg)
{
csn(LOW);
SPI.transfer( R_REGISTER | ( REGISTER_MASK & reg ) );
uint8_t result = SPI.transfer(0xff);
csn(HIGH);
return result;
}
/****************************************************************************/
uint8_t RF24::write_register(uint8_t reg, const uint8_t* buf, uint8_t len)
{
uint8_t status;
csn(LOW);
status = SPI.transfer( W_REGISTER | ( REGISTER_MASK & reg ) );
while ( len-- )
SPI.transfer(*buf++);
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::write_register(uint8_t reg, uint8_t value)
{
uint8_t status;
IF_SERIAL_DEBUG(printf_P(PSTR("write_register(%02x,%02x)\r\n"),reg,value));
csn(LOW);
status = SPI.transfer( W_REGISTER | ( REGISTER_MASK & reg ) );
SPI.transfer(value);
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::write_payload(const void* buf, uint8_t len)
{
uint8_t status;
const uint8_t* current = reinterpret_cast<const uint8_t*>(buf);
uint8_t data_len = min(len,payload_size);
uint8_t blank_len = dynamic_payloads_enabled ? 0 : payload_size - data_len;
//printf("[Writing %u bytes %u blanks]",data_len,blank_len);
csn(LOW);
status = SPI.transfer( W_TX_PAYLOAD );
while ( data_len-- )
SPI.transfer(*current++);
while ( blank_len-- )
SPI.transfer(0);
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::read_payload(void* buf, uint8_t len)
{
uint8_t status;
uint8_t* current = reinterpret_cast<uint8_t*>(buf);
uint8_t data_len = min(len,payload_size);
uint8_t blank_len = dynamic_payloads_enabled ? 0 : payload_size - data_len;
//printf("[Reading %u bytes %u blanks]",data_len,blank_len);
csn(LOW);
status = SPI.transfer( R_RX_PAYLOAD );
while ( data_len-- )
*current++ = SPI.transfer(0xff);
while ( blank_len-- )
SPI.transfer(0xff);
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::flush_rx(void)
{
uint8_t status;
csn(LOW);
status = SPI.transfer( FLUSH_RX );
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::flush_tx(void)
{
uint8_t status;
csn(LOW);
status = SPI.transfer( FLUSH_TX );
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::get_status(void)
{
uint8_t status;
csn(LOW);
status = SPI.transfer( NOP );
csn(HIGH);
return status;
}
/****************************************************************************/
void RF24::print_status(uint8_t status)
{
printf_P(PSTR("STATUS\t\t = 0x%02x RX_DR=%x TX_DS=%x MAX_RT=%x RX_P_NO=%x TX_FULL=%x\r\n"),
status,
(status & _BV(RX_DR))?1:0,
(status & _BV(TX_DS))?1:0,
(status & _BV(MAX_RT))?1:0,
((status >> RX_P_NO) & B111),
(status & _BV(TX_FULL))?1:0
);
}
/****************************************************************************/
void RF24::print_observe_tx(uint8_t value)
{
printf_P(PSTR("OBSERVE_TX=%02x: POLS_CNT=%x ARC_CNT=%x\r\n"),
value,
(value >> PLOS_CNT) & B1111,
(value >> ARC_CNT) & B1111
);
}
/****************************************************************************/
void RF24::print_byte_register(const char* name, uint8_t reg, uint8_t qty)
{
char extra_tab = strlen_P(name) < 8 ? '\t' : 0;
printf_P(PSTR(PRIPSTR"\t%c ="),name,extra_tab);
while (qty--)
printf_P(PSTR(" 0x%02x"),read_register(reg++));
printf_P(PSTR("\r\n"));
}
/****************************************************************************/
void RF24::print_address_register(const char* name, uint8_t reg, uint8_t qty)
{
char extra_tab = strlen_P(name) < 8 ? '\t' : 0;
printf_P(PSTR(PRIPSTR"\t%c ="),name,extra_tab);
while (qty--)
{
uint8_t buffer[5];
read_register(reg++,buffer,sizeof buffer);
printf_P(PSTR(" 0x"));
uint8_t* bufptr = buffer + sizeof buffer;
while( --bufptr >= buffer )
printf_P(PSTR("%02x"),*bufptr);
}
printf_P(PSTR("\r\n"));
}
/****************************************************************************/
RF24::RF24(uint8_t _cepin, uint8_t _cspin):
ce_pin(_cepin), csn_pin(_cspin), wide_band(true), p_variant(false),
payload_size(32), ack_payload_available(false), dynamic_payloads_enabled(false),
pipe0_reading_address(0)
{
}
/****************************************************************************/
void RF24::setChannel(uint8_t channel)
{
// TODO: This method could take advantage of the 'wide_band' calculation
// done in setChannel() to require certain channel spacing.
const uint8_t max_channel = 127;
write_register(RF_CH,min(channel,max_channel));
}
/****************************************************************************/
void RF24::setPayloadSize(uint8_t size)
{
const uint8_t max_payload_size = 32;
payload_size = min(size,max_payload_size);
}
/****************************************************************************/
uint8_t RF24::getPayloadSize(void)
{
return payload_size;
}
/****************************************************************************/
static const char rf24_datarate_e_str_0[] PROGMEM = "1MBPS";
static const char rf24_datarate_e_str_1[] PROGMEM = "2MBPS";
static const char rf24_datarate_e_str_2[] PROGMEM = "250KBPS";
static const char * const rf24_datarate_e_str_P[] PROGMEM = {
rf24_datarate_e_str_0,
rf24_datarate_e_str_1,
rf24_datarate_e_str_2,
};
static const char rf24_model_e_str_0[] PROGMEM = "nRF24L01";
static const char rf24_model_e_str_1[] PROGMEM = "nRF24L01+";
static const char * const rf24_model_e_str_P[] PROGMEM = {
rf24_model_e_str_0,
rf24_model_e_str_1,
};
static const char rf24_crclength_e_str_0[] PROGMEM = "Disabled";
static const char rf24_crclength_e_str_1[] PROGMEM = "8 bits";
static const char rf24_crclength_e_str_2[] PROGMEM = "16 bits" ;
static const char * const rf24_crclength_e_str_P[] PROGMEM = {
rf24_crclength_e_str_0,
rf24_crclength_e_str_1,
rf24_crclength_e_str_2,
};
static const char rf24_pa_dbm_e_str_0[] PROGMEM = "PA_MIN";
static const char rf24_pa_dbm_e_str_1[] PROGMEM = "PA_LOW";
static const char rf24_pa_dbm_e_str_2[] PROGMEM = "LA_MED";
static const char rf24_pa_dbm_e_str_3[] PROGMEM = "PA_HIGH";
static const char * const rf24_pa_dbm_e_str_P[] PROGMEM = {
rf24_pa_dbm_e_str_0,
rf24_pa_dbm_e_str_1,
rf24_pa_dbm_e_str_2,
rf24_pa_dbm_e_str_3,
};
void RF24::printDetails(void)
{
print_status(get_status());
print_address_register(PSTR("RX_ADDR_P0-1"),RX_ADDR_P0,2);
print_byte_register(PSTR("RX_ADDR_P2-5"),RX_ADDR_P2,4);
print_address_register(PSTR("TX_ADDR"),TX_ADDR);
print_byte_register(PSTR("RX_PW_P0-6"),RX_PW_P0,6);
print_byte_register(PSTR("EN_AA"),EN_AA);
print_byte_register(PSTR("EN_RXADDR"),EN_RXADDR);
print_byte_register(PSTR("RF_CH"),RF_CH);
print_byte_register(PSTR("RF_SETUP"),RF_SETUP);
print_byte_register(PSTR("CONFIG"),CONFIG);
print_byte_register(PSTR("DYNPD/FEATURE"),DYNPD,2);
printf_P(PSTR("Data Rate\t = %S\r\n"),pgm_read_word(&rf24_datarate_e_str_P[getDataRate()]));
printf_P(PSTR("Model\t\t = %S\r\n"),pgm_read_word(&rf24_model_e_str_P[isPVariant()]));
printf_P(PSTR("CRC Length\t = %S\r\n"),pgm_read_word(&rf24_crclength_e_str_P[getCRCLength()]));
printf_P(PSTR("PA Power\t = %S\r\n"),pgm_read_word(&rf24_pa_dbm_e_str_P[getPALevel()]));
}
/****************************************************************************/
void RF24::begin(void)
{
// Initialize pins
pinMode(ce_pin,OUTPUT);
pinMode(csn_pin,OUTPUT);
// Initialize SPI bus
SPI.begin();
ce(LOW);
csn(HIGH);
// Must allow the radio time to settle else configuration bits will not necessarily stick.
// This is actually only required following power up but some settling time also appears to
// be required after resets too. For full coverage, we'll always assume the worst.
// Enabling 16b CRC is by far the most obvious case if the wrong timing is used - or skipped.
// Technically we require 4.5ms + 14us as a worst case. We'll just call it 5ms for good measure.
// WARNING: Delay is based on P-variant whereby non-P *may* require different timing.
_delay_ms( 5 ) ;
// Set 1500uS (minimum for 32B payload in ESB@250KBPS) timeouts, to make testing a little easier
// WARNING: If this is ever lowered, either 250KBS mode with AA is broken or maximum packet
// sizes must never be used. See documentation for a more complete explanation.
write_register(SETUP_RETR,(B0100 << ARD) | (B1111 << ARC));
// Restore our default PA level
setPALevel( RF24_PA_MAX ) ;
// Determine if this is a p or non-p RF24 module and then
// reset our data rate back to default value. This works
// because a non-P variant won't allow the data rate to
// be set to 250Kbps.
if( setDataRate( RF24_250KBPS ) )
{
p_variant = true ;
}
// Then set the data rate to the slowest (and most reliable) speed supported by all
// hardware.
setDataRate( RF24_1MBPS ) ;
// Initialize CRC and request 2-byte (16bit) CRC
setCRCLength( RF24_CRC_16 ) ;
// Disable dynamic payloads, to match dynamic_payloads_enabled setting
write_register(DYNPD,0);
// Reset current status
// Notice reset and flush is the last thing we do
write_register(STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) );
// Set up default configuration. Callers can always change it later.
// This channel should be universally safe and not bleed over into adjacent
// spectrum.
setChannel(76);
// Flush buffers
flush_rx();
flush_tx();
}
/****************************************************************************/
void RF24::startListening(void)
{
write_register(CONFIG, read_register(CONFIG) | _BV(PWR_UP) | _BV(PRIM_RX));
write_register(STATUS, _BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) );
// Restore the pipe0 adddress, if exists
if (pipe0_reading_address)
write_register(RX_ADDR_P0, reinterpret_cast<const uint8_t*>(&pipe0_reading_address), 5);
// Flush buffers
flush_rx();
flush_tx();
// Go!
ce(HIGH);
// wait for the radio to come up (130us actually only needed)
delayMicroseconds(130);
}
/****************************************************************************/
void RF24::stopListening(void)
{
ce(LOW);
flush_tx();
flush_rx();
}
/****************************************************************************/
void RF24::powerDown(void)
{
write_register(CONFIG,read_register(CONFIG) & ~_BV(PWR_UP));
}
/****************************************************************************/
void RF24::powerUp(void)
{
write_register(CONFIG,read_register(CONFIG) | _BV(PWR_UP));
}
/******************************************************************/
bool RF24::write( const void* buf, uint8_t len )
{
bool result = false;
// Begin the write
startWrite(buf,len);
// ------------
// At this point we could return from a non-blocking write, and then call
// the rest after an interrupt
// Instead, we are going to block here until we get TX_DS (transmission completed and ack'd)
// or MAX_RT (maximum retries, transmission failed). Also, we'll timeout in case the radio
// is flaky and we get neither.
// IN the end, the send should be blocking. It comes back in 60ms worst case, or much faster
// if I tighted up the retry logic. (Default settings will be 1500us.
// Monitor the send
uint8_t observe_tx;
uint8_t status;
uint32_t sent_at = millis();
const uint32_t timeout = 500; //ms to wait for timeout
do
{
status = read_register(OBSERVE_TX,&observe_tx,1);
IF_SERIAL_DEBUG(Serial.print(observe_tx,HEX));
}
while( ! ( status & ( _BV(TX_DS) | _BV(MAX_RT) ) ) && ( millis() - sent_at < timeout ) );
// The part above is what you could recreate with your own interrupt handler,
// and then call this when you got an interrupt
// ------------
// Call this when you get an interrupt
// The status tells us three things
// * The send was successful (TX_DS)
// * The send failed, too many retries (MAX_RT)
// * There is an ack packet waiting (RX_DR)
bool tx_ok, tx_fail;
whatHappened(tx_ok,tx_fail,ack_payload_available);
//printf("%u%u%u\r\n",tx_ok,tx_fail,ack_payload_available);
result = tx_ok;
IF_SERIAL_DEBUG(Serial.print(result?"...OK.":"...Failed"));
// Handle the ack packet
if ( ack_payload_available )
{
ack_payload_length = getDynamicPayloadSize();
IF_SERIAL_DEBUG(Serial.print("[AckPacket]/"));
IF_SERIAL_DEBUG(Serial.println(ack_payload_length,DEC));
}
// Yay, we are done.
// Power down
powerDown();
// Flush buffers (Is this a relic of past experimentation, and not needed anymore??)
flush_tx();
return result;
}
/****************************************************************************/
void RF24::startWrite( const void* buf, uint8_t len )
{
// Transmitter power-up
write_register(CONFIG, ( read_register(CONFIG) | _BV(PWR_UP) ) & ~_BV(PRIM_RX) );
delayMicroseconds(150);
// Send the payload
write_payload( buf, len );
// Allons!
ce(HIGH);
delayMicroseconds(15);
ce(LOW);
}
/****************************************************************************/
uint8_t RF24::getDynamicPayloadSize(void)
{
uint8_t result = 0;
csn(LOW);
SPI.transfer( R_RX_PL_WID );
result = SPI.transfer(0xff);
csn(HIGH);
return result;
}
/****************************************************************************/
bool RF24::available(void)
{
return available(NULL);
}
/****************************************************************************/
bool RF24::available(uint8_t* pipe_num)
{
uint8_t status = get_status();
// Too noisy, enable if you really want lots o data!!
//IF_SERIAL_DEBUG(print_status(status));
bool result = ( status & _BV(RX_DR) );
if (result)
{
// If the caller wants the pipe number, include that
if ( pipe_num )
*pipe_num = ( status >> RX_P_NO ) & B111;
// Clear the status bit
// ??? Should this REALLY be cleared now? Or wait until we
// actually READ the payload?
write_register(STATUS,_BV(RX_DR) );
// Handle ack payload receipt
if ( status & _BV(TX_DS) )
{
write_register(STATUS,_BV(TX_DS));
}
}
return result;
}
/****************************************************************************/
bool RF24::read( void* buf, uint8_t len )
{
// Fetch the payload
read_payload( buf, len );
// was this the last of the data available?
return read_register(FIFO_STATUS) & _BV(RX_EMPTY);
}
/****************************************************************************/
void RF24::whatHappened(bool& tx_ok,bool& tx_fail,bool& rx_ready)
{
// Read the status & reset the status in one easy call
// Or is that such a good idea?
uint8_t status = write_register(STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) );
// Report to the user what happened
tx_ok = status & _BV(TX_DS);
tx_fail = status & _BV(MAX_RT);
rx_ready = status & _BV(RX_DR);
}
/****************************************************************************/
void RF24::openWritingPipe(uint64_t value)
{
// Note that AVR 8-bit uC's store this LSB first, and the NRF24L01(+)
// expects it LSB first too, so we're good.
write_register(RX_ADDR_P0, reinterpret_cast<uint8_t*>(&value), 5);
write_register(TX_ADDR, reinterpret_cast<uint8_t*>(&value), 5);
const uint8_t max_payload_size = 32;
write_register(RX_PW_P0,min(payload_size,max_payload_size));
}
/****************************************************************************/
static const uint8_t child_pipe[] PROGMEM =
{
RX_ADDR_P0, RX_ADDR_P1, RX_ADDR_P2, RX_ADDR_P3, RX_ADDR_P4, RX_ADDR_P5
};
static const uint8_t child_payload_size[] PROGMEM =
{
RX_PW_P0, RX_PW_P1, RX_PW_P2, RX_PW_P3, RX_PW_P4, RX_PW_P5
};
static const uint8_t child_pipe_enable[] PROGMEM =
{
ERX_P0, ERX_P1, ERX_P2, ERX_P3, ERX_P4, ERX_P5
};
void RF24::openReadingPipe(uint8_t child, uint64_t address)
{
// If this is pipe 0, cache the address. This is needed because
// openWritingPipe() will overwrite the pipe 0 address, so
// startListening() will have to restore it.
if (child == 0)
pipe0_reading_address = address;
if (child <= 6)
{
// For pipes 2-5, only write the LSB
if ( child < 2 )
write_register(pgm_read_byte(&child_pipe[child]), reinterpret_cast<const uint8_t*>(&address), 5);
else
write_register(pgm_read_byte(&child_pipe[child]), reinterpret_cast<const uint8_t*>(&address), 1);
write_register(pgm_read_byte(&child_payload_size[child]),payload_size);
// Note it would be more efficient to set all of the bits for all open
// pipes at once. However, I thought it would make the calling code
// more simple to do it this way.
write_register(EN_RXADDR,read_register(EN_RXADDR) | _BV(pgm_read_byte(&child_pipe_enable[child])));
}
}
/****************************************************************************/
void RF24::toggle_features(void)
{
csn(LOW);
SPI.transfer( ACTIVATE );
SPI.transfer( 0x73 );
csn(HIGH);
}
/****************************************************************************/
void RF24::enableDynamicPayloads(void)
{
// Enable dynamic payload throughout the system
write_register(FEATURE,read_register(FEATURE) | _BV(EN_DPL) );
// If it didn't work, the features are not enabled
if ( ! read_register(FEATURE) )
{
// So enable them and try again
toggle_features();
write_register(FEATURE,read_register(FEATURE) | _BV(EN_DPL) );
}
IF_SERIAL_DEBUG(printf("FEATURE=%i\r\n",read_register(FEATURE)));
// Enable dynamic payload on all pipes
//
// Not sure the use case of only having dynamic payload on certain
// pipes, so the library does not support it.
write_register(DYNPD,read_register(DYNPD) | _BV(DPL_P5) | _BV(DPL_P4) | _BV(DPL_P3) | _BV(DPL_P2) | _BV(DPL_P1) | _BV(DPL_P0));
dynamic_payloads_enabled = true;
}
/****************************************************************************/
void RF24::enableAckPayload(void)
{
//
// enable ack payload and dynamic payload features
//
write_register(FEATURE,read_register(FEATURE) | _BV(EN_ACK_PAY) | _BV(EN_DPL) );
// If it didn't work, the features are not enabled
if ( ! read_register(FEATURE) )
{
// So enable them and try again
toggle_features();
write_register(FEATURE,read_register(FEATURE) | _BV(EN_ACK_PAY) | _BV(EN_DPL) );
}
IF_SERIAL_DEBUG(printf("FEATURE=%i\r\n",read_register(FEATURE)));
//
// Enable dynamic payload on pipes 0 & 1
//
write_register(DYNPD,read_register(DYNPD) | _BV(DPL_P1) | _BV(DPL_P0));
}
/****************************************************************************/
void RF24::writeAckPayload(uint8_t pipe, const void* buf, uint8_t len)
{
const uint8_t* current = reinterpret_cast<const uint8_t*>(buf);
csn(LOW);
SPI.transfer( W_ACK_PAYLOAD | ( pipe & B111 ) );
const uint8_t max_payload_size = 32;
uint8_t data_len = min(len,max_payload_size);
while ( data_len-- )
SPI.transfer(*current++);
csn(HIGH);
}
/****************************************************************************/
bool RF24::isAckPayloadAvailable(void)
{
bool result = ack_payload_available;
ack_payload_available = false;
return result;
}
/****************************************************************************/
bool RF24::isPVariant(void)
{
return p_variant ;
}
/****************************************************************************/
void RF24::setAutoAck(bool enable)
{
if ( enable )
write_register(EN_AA, B111111);
else
write_register(EN_AA, 0);
}
/****************************************************************************/
void RF24::setAutoAck( uint8_t pipe, bool enable )
{
if ( pipe <= 6 )
{
uint8_t en_aa = read_register( EN_AA ) ;
if( enable )
{
en_aa |= _BV(pipe) ;
}
else
{
en_aa &= ~_BV(pipe) ;
}
write_register( EN_AA, en_aa ) ;
}
}
/****************************************************************************/
bool RF24::testCarrier(void)
{
return ( read_register(CD) & 1 );
}
/****************************************************************************/
bool RF24::testRPD(void)
{
return ( read_register(RPD) & 1 ) ;
}
/****************************************************************************/
void RF24::setPALevel(rf24_pa_dbm_e level)
{
uint8_t setup = read_register(RF_SETUP) ;
setup &= ~(_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH)) ;
// switch uses RAM (evil!)
if ( level == RF24_PA_MAX )
{
setup |= (_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH)) ;
}
else if ( level == RF24_PA_HIGH )
{
setup |= _BV(RF_PWR_HIGH) ;
}
else if ( level == RF24_PA_LOW )
{
setup |= _BV(RF_PWR_LOW);
}
else if ( level == RF24_PA_MIN )
{
// nothing
}
else if ( level == RF24_PA_ERROR )
{
// On error, go to maximum PA
setup |= (_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH)) ;
}
write_register( RF_SETUP, setup ) ;
}
/****************************************************************************/
rf24_pa_dbm_e RF24::getPALevel(void)
{
rf24_pa_dbm_e result = RF24_PA_ERROR ;
uint8_t power = read_register(RF_SETUP) & (_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH)) ;
// switch uses RAM (evil!)
if ( power == (_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH)) )
{
result = RF24_PA_MAX ;
}
else if ( power == _BV(RF_PWR_HIGH) )
{
result = RF24_PA_HIGH ;
}
else if ( power == _BV(RF_PWR_LOW) )
{
result = RF24_PA_LOW ;
}
else
{
result = RF24_PA_MIN ;
}
return result ;
}
/****************************************************************************/
bool RF24::setDataRate(rf24_datarate_e speed)
{
bool result = false;
uint8_t setup = read_register(RF_SETUP) ;
// HIGH and LOW '00' is 1Mbs - our default
wide_band = false ;
setup &= ~(_BV(RF_DR_LOW) | _BV(RF_DR_HIGH)) ;
if( speed == RF24_250KBPS )
{
// Must set the RF_DR_LOW to 1; RF_DR_HIGH (used to be RF_DR) is already 0
// Making it '10'.
wide_band = false ;
setup |= _BV( RF_DR_LOW ) ;
}
else
{
// Set 2Mbs, RF_DR (RF_DR_HIGH) is set 1
// Making it '01'
if ( speed == RF24_2MBPS )
{
wide_band = true ;
setup |= _BV(RF_DR_HIGH);
}
else
{
// 1Mbs
wide_band = false ;
}
}
write_register(RF_SETUP,setup);
// Verify our result
if ( read_register(RF_SETUP) == setup )
{
result = true;
}
else
{
wide_band = false;
}
return result;
}
/****************************************************************************/
rf24_datarate_e RF24::getDataRate( void )
{
rf24_datarate_e result ;
uint8_t dr = read_register(RF_SETUP) & (_BV(RF_DR_LOW) | _BV(RF_DR_HIGH));
// switch uses RAM (evil!)
// Order matters in our case below
if ( dr == _BV(RF_DR_LOW) )
{
// '10' = 250KBPS
result = RF24_250KBPS ;
}
else if ( dr == _BV(RF_DR_HIGH) )
{
// '01' = 2MBPS
result = RF24_2MBPS ;
}
else
{
// '00' = 1MBPS
result = RF24_1MBPS ;
}
return result ;
}
/****************************************************************************/
void RF24::setCRCLength(rf24_crclength_e length)
{
uint8_t config = read_register(CONFIG) & ~( _BV(CRCO) | _BV(EN_CRC)) ;
// switch uses RAM (evil!)
if ( length == RF24_CRC_DISABLED )
{
// Do nothing, we turned it off above.
}
else if ( length == RF24_CRC_8 )
{
config |= _BV(EN_CRC);
}
else
{
config |= _BV(EN_CRC);
config |= _BV( CRCO );
}
write_register( CONFIG, config ) ;
}
/****************************************************************************/
rf24_crclength_e RF24::getCRCLength(void)
{
rf24_crclength_e result = RF24_CRC_DISABLED;
uint8_t config = read_register(CONFIG) & ( _BV(CRCO) | _BV(EN_CRC)) ;
if ( config & _BV(EN_CRC ) )
{
if ( config & _BV(CRCO) )
result = RF24_CRC_16;
else
result = RF24_CRC_8;
}
return result;
}
/****************************************************************************/
void RF24::disableCRC( void )
{
uint8_t disable = read_register(CONFIG) & ~_BV(EN_CRC) ;
write_register( CONFIG, disable ) ;
}
/****************************************************************************/
void RF24::setRetries(uint8_t delay, uint8_t count)
{
write_register(SETUP_RETR,(delay&0xf)<<ARD | (count&0xf)<<ARC);
}
// vim:ai:cin:sts=2 sw=2 ft=cpp

819
arduino/libraries/RF24/RF24.h
Unescape View File

@ -0,0 +1,819 @@
/*
Copyright (C) 2011 J. Coliz <maniacbug@ymail.com>
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
version 2 as published by the Free Software Foundation.
*/
/**
* @file RF24.h
*
* Class declaration for RF24 and helper enums
*/
#ifndef __RF24_H__
#define __RF24_H__
#include <RF24_config.h>
#include <Arduino.h>
/**
* Power Amplifier level.
*
* For use with setPALevel()
*/
typedef enum { RF24_PA_MIN = 0,RF24_PA_LOW, RF24_PA_HIGH, RF24_PA_MAX, RF24_PA_ERROR } rf24_pa_dbm_e ;
/**
* Data rate. How fast data moves through the air.
*
* For use with setDataRate()
*/
typedef enum { RF24_1MBPS = 0, RF24_2MBPS, RF24_250KBPS } rf24_datarate_e;
/**
* CRC Length. How big (if any) of a CRC is included.
*
* For use with setCRCLength()
*/
typedef enum { RF24_CRC_DISABLED = 0, RF24_CRC_8, RF24_CRC_16 } rf24_crclength_e;
/**
* Driver for nRF24L01(+) 2.4GHz Wireless Transceiver
*/
class RF24
{
private:
uint8_t ce_pin; /**< "Chip Enable" pin, activates the RX or TX role */
uint8_t csn_pin; /**< SPI Chip select */
bool wide_band; /* 2Mbs data rate in use? */
bool p_variant; /* False for RF24L01 and true for RF24L01P */
uint8_t payload_size; /**< Fixed size of payloads */
bool ack_payload_available; /**< Whether there is an ack payload waiting */
bool dynamic_payloads_enabled; /**< Whether dynamic payloads are enabled. */
uint8_t ack_payload_length; /**< Dynamic size of pending ack payload. */
uint64_t pipe0_reading_address; /**< Last address set on pipe 0 for reading. */
public:
/**
* @name Low-level internal interface.
*
* Protected methods that address the chip directly. Regular users cannot
* ever call these. They are documented for completeness and for developers who
* may want to extend this class.
*/
/**@{*/
/**
* Set chip select pin
*
* Running SPI bus at PI_CLOCK_DIV2 so we don't waste time transferring data
* and best of all, we make use of the radio's FIFO buffers. A lower speed
* means we're less likely to effectively leverage our FIFOs and pay a higher
* AVR runtime cost as toll.
*
* @param mode HIGH to take this unit off the SPI bus, LOW to put it on
*/
void csn(int mode);
/**
* Set chip enable
*
* @param level HIGH to actively begin transmission or LOW to put in standby. Please see data sheet
* for a much more detailed description of this pin.
*/
void ce(int level);
/**
* Read a chunk of data in from a register
*
* @param reg Which register. Use constants from nRF24L01.h
* @param buf Where to put the data
* @param len How many bytes of data to transfer
* @return Current value of status register
*/
uint8_t read_register(uint8_t reg, uint8_t* buf, uint8_t len);
/**
* Read single byte from a register
*
* @param reg Which register. Use constants from nRF24L01.h
* @return Current value of register @p reg
*/
uint8_t read_register(uint8_t reg);
/**
* Write a chunk of data to a register
*
* @param reg Which register. Use constants from nRF24L01.h
* @param buf Where to get the data
* @param len How many bytes of data to transfer
* @return Current value of status register
*/
uint8_t write_register(uint8_t reg, const uint8_t* buf, uint8_t len);
/**
* Write a single byte to a register
*
* @param reg Which register. Use constants from nRF24L01.h
* @param value The new value to write
* @return Current value of status register
*/
uint8_t write_register(uint8_t reg, uint8_t value);
/**
* Write the transmit payload
*
* The size of data written is the fixed payload size, see getPayloadSize()
*
* @param buf Where to get the data
* @param len Number of bytes to be sent
* @return Current value of status register
*/
uint8_t write_payload(const void* buf, uint8_t len);
/**
* Read the receive payload
*
* The size of data read is the fixed payload size, see getPayloadSize()
*
* @param buf Where to put the data
* @param len Maximum number of bytes to read
* @return Current value of status register
*/
uint8_t read_payload(void* buf, uint8_t len);
/**
* Empty the receive buffer
*
* @return Current value of status register
*/
uint8_t flush_rx(void);
/**
* Empty the transmit buffer
*
* @return Current value of status register
*/
uint8_t flush_tx(void);
/**
* Retrieve the current status of the chip
*
* @return Current value of status register
*/
uint8_t get_status(void);
/**
* Decode and print the given status to stdout
*
* @param status Status value to print
*
* @warning Does nothing if stdout is not defined. See fdevopen in stdio.h
*/
void print_status(uint8_t status);
/**
* Decode and print the given 'observe_tx' value to stdout
*
* @param value The observe_tx value to print
*
* @warning Does nothing if stdout is not defined. See fdevopen in stdio.h
*/
void print_observe_tx(uint8_t value);
/**
* Print the name and value of an 8-bit register to stdout
*
* Optionally it can print some quantity of successive
* registers on the same line. This is useful for printing a group
* of related registers on one line.
*
* @param name Name of the register
* @param reg Which register. Use constants from nRF24L01.h
* @param qty How many successive registers to print
*/
void print_byte_register(const char* name, uint8_t reg, uint8_t qty = 1);
/**
* Print the name and value of a 40-bit address register to stdout
*
* Optionally it can print some quantity of successive
* registers on the same line. This is useful for printing a group
* of related registers on one line.
*
* @param name Name of the register
* @param reg Which register. Use constants from nRF24L01.h
* @param qty How many successive registers to print
*/
void print_address_register(const char* name, uint8_t reg, uint8_t qty = 1);
/**
* Turn on or off the special features of the chip
*
* The chip has certain 'features' which are only available when the 'features'
* are enabled. See the datasheet for details.
*/
void toggle_features(void);
/**@}*/
//public:
/**
* @name Primary public interface
*
* These are the main methods you need to operate the chip
*/
/**@{*/
/**
* Constructor
*
* Creates a new instance of this driver. Before using, you create an instance
* and send in the unique pins that this chip is connected to.
*
* @param _cepin The pin attached to Chip Enable on the RF module
* @param _cspin The pin attached to Chip Select
*/
RF24(uint8_t _cepin, uint8_t _cspin);
/**
* Begin operation of the chip
*
* Call this in setup(), before calling any other methods.
*/
void begin(void);
/**
* Start listening on the pipes opened for reading.
*
* Be sure to call openReadingPipe() first. Do not call write() while
* in this mode, without first calling stopListening(). Call
* isAvailable() to check for incoming traffic, and read() to get it.
*/
void startListening(void);
/**
* Stop listening for incoming messages
*
* Do this before calling write().
*/
void stopListening(void);
/**
* Write to the open writing pipe
*
* Be sure to call openWritingPipe() first to set the destination
* of where to write to.
*
* This blocks until the message is successfully acknowledged by
* the receiver or the timeout/retransmit maxima are reached. In
* the current configuration, the max delay here is 60ms.
*
* The maximum size of data written is the fixed payload size, see
* getPayloadSize(). However, you can write less, and the remainder
* will just be filled with zeroes.
*
* @param buf Pointer to the data to be sent
* @param len Number of bytes to be sent
* @return True if the payload was delivered successfully false if not
*/
bool write( const void* buf, uint8_t len );
/**
* Test whether there are bytes available to be read
*
* @return True if there is a payload available, false if none is
*/
bool available(void);
/**
* Read the payload
*
* Return the last payload received
*
* The size of data read is the fixed payload size, see getPayloadSize()
*
* @note I specifically chose 'void*' as a data type to make it easier
* for beginners to use. No casting needed.
*
* @param buf Pointer to a buffer where the data should be written
* @param len Maximum number of bytes to read into the buffer
* @return True if the payload was delivered successfully false if not
*/
bool read( void* buf, uint8_t len );
/**
* Open a pipe for writing
*
* Only one pipe can be open at once, but you can change the pipe
* you'll listen to. Do not call this while actively listening.
* Remember to stopListening() first.
*
* Addresses are 40-bit hex values, e.g.:
*
* @code
* openWritingPipe(0xF0F0F0F0F0);
* @endcode
*
* @param address The 40-bit address of the pipe to open. This can be
* any value whatsoever, as long as you are the only one writing to it
* and only one other radio is listening to it. Coordinate these pipe
* addresses amongst nodes on the network.
*/
void openWritingPipe(uint64_t address);
/**
* Open a pipe for reading
*
* Up to 6 pipes can be open for reading at once. Open all the
* reading pipes, and then call startListening().
*
* @see openWritingPipe
*
* @warning Pipes 1-5 should share the first 32 bits.
* Only the least significant byte should be unique, e.g.
* @code
* openReadingPipe(1,0xF0F0F0F0AA);
* openReadingPipe(2,0xF0F0F0F066);
* @endcode
*
* @warning Pipe 0 is also used by the writing pipe. So if you open
* pipe 0 for reading, and then startListening(), it will overwrite the
* writing pipe. Ergo, do an openWritingPipe() again before write().
*
* @todo Enforce the restriction that pipes 1-5 must share the top 32 bits
*
* @param number Which pipe# to open, 0-5.
* @param address The 40-bit address of the pipe to open.
*/
void openReadingPipe(uint8_t number, uint64_t address);
/**@}*/
/**
* @name Optional Configurators
*
* Methods you can use to get or set the configuration of the chip.
* None are required. Calling begin() sets up a reasonable set of
* defaults.
*/
/**@{*/
/**
* Set the number and delay of retries upon failed submit
*
* @param delay How long to wait between each retry, in multiples of 250us,
* max is 15. 0 means 250us, 15 means 4000us.
* @param count How many retries before giving up, max 15
*/
void setRetries(uint8_t delay, uint8_t count);
/**
* Set RF communication channel
*
* @param channel Which RF channel to communicate on, 0-127
*/
void setChannel(uint8_t channel);
/**
* Set Static Payload Size
*
* This implementation uses a pre-stablished fixed payload size for all
* transmissions. If this method is never called, the driver will always
* transmit the maximum payload size (32 bytes), no matter how much
* was sent to write().
*
* @todo Implement variable-sized payloads feature
*
* @param size The number of bytes in the payload
*/
void setPayloadSize(uint8_t size);
/**
* Get Static Payload Size
*
* @see setPayloadSize()
*
* @return The number of bytes in the payload
*/
uint8_t getPayloadSize(void);
/**
* Get Dynamic Payload Size
*
* For dynamic payloads, this pulls the size of the payload off
* the chip
*
* @return Payload length of last-received dynamic payload
*/
uint8_t getDynamicPayloadSize(void);
/**
* Enable custom payloads on the acknowledge packets
*
* Ack payloads are a handy way to return data back to senders without
* manually changing the radio modes on both units.
*
* @see examples/pingpair_pl/pingpair_pl.pde
*/
void enableAckPayload(void);
/**
* Enable dynamically-sized payloads
*
* This way you don't always have to send large packets just to send them
* once in a while. This enables dynamic payloads on ALL pipes.
*
* @see examples/pingpair_pl/pingpair_dyn.pde
*/
void enableDynamicPayloads(void);
/**
* Determine whether the hardware is an nRF24L01+ or not.
*
* @return true if the hardware is nRF24L01+ (or compatible) and false
* if its not.
*/
bool isPVariant(void) ;
/**
* Enable or disable auto-acknowlede packets
*
* This is enabled by default, so it's only needed if you want to turn
* it off for some reason.
*
* @param enable Whether to enable (true) or disable (false) auto-acks
*/
void setAutoAck(bool enable);
/**
* Enable or disable auto-acknowlede packets on a per pipeline basis.
*
* AA is enabled by default, so it's only needed if you want to turn
* it off/on for some reason on a per pipeline basis.
*
* @param pipe Which pipeline to modify
* @param enable Whether to enable (true) or disable (false) auto-acks
*/
void setAutoAck( uint8_t pipe, bool enable ) ;
/**
* Set Power Amplifier (PA) level to one of four levels.
* Relative mnemonics have been used to allow for future PA level
* changes. According to 6.5 of the nRF24L01+ specification sheet,
* they translate to: RF24_PA_MIN=-18dBm, RF24_PA_LOW=-12dBm,
* RF24_PA_MED=-6dBM, and RF24_PA_HIGH=0dBm.
*
* @param level Desired PA level.
*/
void setPALevel( rf24_pa_dbm_e level ) ;
/**
* Fetches the current PA level.
*
* @return Returns a value from the rf24_pa_dbm_e enum describing
* the current PA setting. Please remember, all values represented
* by the enum mnemonics are negative dBm. See setPALevel for
* return value descriptions.
*/
rf24_pa_dbm_e getPALevel( void ) ;
/**
* Set the transmission data rate
*
* @warning setting RF24_250KBPS will fail for non-plus units
*
* @param speed RF24_250KBPS for 250kbs, RF24_1MBPS for 1Mbps, or RF24_2MBPS for 2Mbps
* @return true if the change was successful
*/
bool setDataRate(rf24_datarate_e speed);
/**
* Fetches the transmission data rate
*
* @return Returns the hardware's currently configured datarate. The value
* is one of 250kbs, RF24_1MBPS for 1Mbps, or RF24_2MBPS, as defined in the
* rf24_datarate_e enum.
*/
rf24_datarate_e getDataRate( void ) ;
/**
* Set the CRC length
*
* @param length RF24_CRC_8 for 8-bit or RF24_CRC_16 for 16-bit
*/
void setCRCLength(rf24_crclength_e length);
/**
* Get the CRC length
*
* @return RF24_DISABLED if disabled or RF24_CRC_8 for 8-bit or RF24_CRC_16 for 16-bit
*/
rf24_crclength_e getCRCLength(void);
/**
* Disable CRC validation
*
*/
void disableCRC( void ) ;
/**@}*/
/**
* @name Advanced Operation
*
* Methods you can use to drive the chip in more advanced ways
*/
/**@{*/
/**
* Print a giant block of debugging information to stdout
*
* @warning Does nothing if stdout is not defined. See fdevopen in stdio.h
*/
void printDetails(void);
/**
* Enter low-power mode
*
* To return to normal power mode, either write() some data or
* startListening, or powerUp().
*/
void powerDown(void);
/**
* Leave low-power mode - making radio more responsive
*
* To return to low power mode, call powerDown().
*/
void powerUp(void) ;
/**
* Test whether there are bytes available to be read
*
* Use this version to discover on which pipe the message
* arrived.
*
* @param[out] pipe_num Which pipe has the payload available
* @return True if there is a payload available, false if none is
*/
bool available(uint8_t* pipe_num);
/**
* Non-blocking write to the open writing pipe
*
* Just like write(), but it returns immediately. To find out what happened
* to the send, catch the IRQ and then call whatHappened().
*
* @see write()
* @see whatHappened()
*
* @param buf Pointer to the data to be sent
* @param len Number of bytes to be sent
* @return True if the payload was delivered successfully false if not
*/
void startWrite( const void* buf, uint8_t len );
/**
* Write an ack payload for the specified pipe
*
* The next time a message is received on @p pipe, the data in @p buf will
* be sent back in the acknowledgement.
*
* @warning According to the data sheet, only three of these can be pending
* at any time. I have not tested this.
*
* @param pipe Which pipe# (typically 1-5) will get this response.
* @param buf Pointer to data that is sent
* @param len Length of the data to send, up to 32 bytes max. Not affected
* by the static payload set by setPayloadSize().
*/
void writeAckPayload(uint8_t pipe, const void* buf, uint8_t len);
/**
* Determine if an ack payload was received in the most recent call to
* write().
*
* Call read() to retrieve the ack payload.
*
* @warning Calling this function clears the internal flag which indicates
* a payload is available. If it returns true, you must read the packet
* out as the very next interaction with the radio, or the results are
* undefined.
*
* @return True if an ack payload is available.
*/
bool isAckPayloadAvailable(void);
/**
* Call this when you get an interrupt to find out why
*
* Tells you what caused the interrupt, and clears the state of
* interrupts.
*
* @param[out] tx_ok The send was successful (TX_DS)
* @param[out] tx_fail The send failed, too many retries (MAX_RT)
* @param[out] rx_ready There is a message waiting to be read (RX_DS)
*/
void whatHappened(bool& tx_ok,bool& tx_fail,bool& rx_ready);
/**
* Test whether there was a carrier on the line for the
* previous listening period.
*
* Useful to check for interference on the current channel.
*
* @return true if was carrier, false if not
*/
bool testCarrier(void);
/**
* Test whether a signal (carrier or otherwise) greater than
* or equal to -64dBm is present on the channel. Valid only
* on nRF24L01P (+) hardware. On nRF24L01, use testCarrier().
*
* Useful to check for interference on the current channel and
* channel hopping strategies.
*
* @return true if signal => -64dBm, false if not
*/
bool testRPD(void) ;
/**
* Test whether this is a real radio, or a mock shim for
* debugging. Setting either pin to 0xff is the way to
* indicate that this is not a real radio.
*
* @return true if this is a legitimate radio
*/
bool isValid() { return ce_pin != 0xff && csn_pin != 0xff; }
/**@}*/
};
/**
* @example GettingStarted.pde
*
* This is an example which corresponds to my "Getting Started" blog post:
* <a style="text-align:center" href="http://maniacbug.wordpress.com/2011/11/02/getting-started-rf24/">Getting Started with nRF24L01+ on Arduino</a>.
*
* It is an example of how to use the RF24 class. Write this sketch to two
* different nodes. Put one of the nodes into 'transmit' mode by connecting
* with the serial monitor and sending a 'T'. The ping node sends the current
* time to the pong node, which responds by sending the value back. The ping
* node can then see how long the whole cycle took.
*/
/**
* @example nordic_fob.pde
*
* This is an example of how to use the RF24 class to receive signals from the
* Sparkfun Nordic FOB. See http://www.sparkfun.com/products/8602 .
* Thanks to Kirk Mower for providing test hardware.
*/
/**
* @example led_remote.pde
*
* This is an example of how to use the RF24 class to control a remote
* bank of LED's using buttons on a remote control.
*
* Every time the buttons change on the remote, the entire state of
* buttons is send to the led board, which displays the state.
*/
/**
* @example pingpair.pde
*
* This is an example of how to use the RF24 class. Write this sketch to two
* different nodes, connect the role_pin to ground on one. The ping node sends
* the current time to the pong node, which responds by sending the value back.
* The ping node can then see how long the whole cycle took.
*/
/**
* @example pingpair_maple.pde
*
* This is an example of how to use the RF24 class on the Maple. For a more
* detailed explanation, see my blog post:
* <a href="http://maniacbug.wordpress.com/2011/12/14/nrf24l01-running-on-maple-3/">nRF24L01+ Running on Maple</a>
*
* It will communicate well to an Arduino-based unit as well, so it's not for only Maple-to-Maple communication.
*
* Write this sketch to two different nodes,
* connect the role_pin to ground on one. The ping node sends the current time to the pong node,
* which responds by sending the value back. The ping node can then see how long the whole cycle
* took.
*/
/**
* @example starping.pde
*
* This sketch is a more complex example of using the RF24 library for Arduino.
* Deploy this on up to six nodes. Set one as the 'pong receiver' by tying the
* role_pin low, and the others will be 'ping transmit' units. The ping units
* unit will send out the value of millis() once a second. The pong unit will
* respond back with a copy of the value. Each ping unit can get that response
* back, and determine how long the whole cycle took.
*
* This example requires a bit more complexity to determine which unit is which.
* The pong receiver is identified by having its role_pin tied to ground.
* The ping senders are further differentiated by a byte in eeprom.
*/
/**
* @example pingpair_pl.pde
*
* This is an example of how to do two-way communication without changing
* transmit/receive modes. Here, a payload is set to the transmitter within
* the Ack packet of each transmission. Note that the payload is set BEFORE
* the sender's message arrives.
*/
/**
* @example pingpair_irq.pde
*
* This is an example of how to user interrupts to interact with the radio.
* It builds on the pingpair_pl example, and uses ack payloads.
*/
/**
* @example pingpair_sleepy.pde
*
* This is an example of how to use the RF24 class to create a battery-
* efficient system. It is just like the pingpair.pde example, but the
* ping node powers down the radio and sleeps the MCU after every
* ping/pong cycle.
*/
/**
* @example scanner.pde
*
* Example to detect interference on the various channels available.
* This is a good diagnostic tool to check whether you're picking a
* good channel for your application.
*
* Inspired by cpixip.
* See http://arduino.cc/forum/index.php/topic,54795.0.html
*/
/**
* @mainpage Driver for nRF24L01(+) 2.4GHz Wireless Transceiver
*
* @section Goals Design Goals
*
* This library is designed to be...
* @li Maximally compliant with the intended operation of the chip
* @li Easy for beginners to use
* @li Consumed with a public interface that's similiar to other Arduino standard libraries
*
* @section News News
*
* NOW COMPATIBLE WITH ARDUINO 1.0 - The 'master' branch and all examples work with both Arduino 1.0 and earlier versions.
* Please <a href="https://github.com/maniacbug/RF24/issues/new">open an issue</a> if you find any problems using it with any version of Arduino.
*
* NOW COMPATIBLE WITH MAPLE - RF24 has been tested with the
* <a href="http://leaflabs.com/store/#Maple-Native">Maple Native</a>,
* and should work with any Maple board. See the pingpair_maple example.
* Note that only the pingpair_maple example has been tested on Maple, although
* the others can certainly be adapted.
*
* @section Useful Useful References
*
* Please refer to:
*
* @li <a href="http://maniacbug.github.com/RF24/">Documentation Main Page</a>
* @li <a href="http://maniacbug.github.com/RF24/classRF24.html">RF24 Class Documentation</a>
* @li <a href="https://github.com/maniacbug/RF24/">Source Code</a>
* @li <a href="https://github.com/maniacbug/RF24/archives/master">Downloads Page</a>
* @li <a href="http://www.nordicsemi.com/files/Product/data_sheet/nRF24L01_Product_Specification_v2_0.pdf">Chip Datasheet</a>
*
* This chip uses the SPI bus, plus two chip control pins. Remember that pin 10 must still remain an output, or
* the SPI hardware will go into 'slave' mode.
*
* @section More More Information
*
* @subpage FAQ
*
* @section Projects Projects
*
* Stuff I have built with RF24
*
* <img src="http://farm7.staticflickr.com/6044/6307669179_a8d19298a6_m.jpg" width="240" height="160" alt="RF24 Getting Started - Finished Product">
*
* <a style="text-align:center" href="http://maniacbug.wordpress.com/2011/11/02/getting-started-rf24/">Getting Started with nRF24L01+ on Arduino</a>
*
* <img src="http://farm8.staticflickr.com/7159/6645514331_38eb2bdeaa_m.jpg" width="240" height="160" alt="Nordic FOB and nRF24L01+">
*
* <a style="text-align:center" href="http://maniacbug.wordpress.com/2012/01/08/nordic-fob/">Using the Sparkfun Nordic FOB</a>
*
* <img src="http://farm7.staticflickr.com/6097/6224308836_b9b3b421a3_m.jpg" width="240" height="160" alt="RF Duinode V3 (2V4)">
*
* <a href="http://maniacbug.wordpress.com/2011/10/19/sensor-node/">Low-Power Wireless Sensor Node</a>
*
* <img src="http://farm8.staticflickr.com/7012/6489477865_b56edb629b_m.jpg" width="240" height="161" alt="nRF24L01+ connected to Leaf Labs Maple Native">
*
* <a href="http://maniacbug.wordpress.com/2011/12/14/nrf24l01-running-on-maple-3/">nRF24L01+ Running on Maple</a>
*/
#endif // __RF24_H__
// vim:ai:cin:sts=2 sw=2 ft=cpp

65
arduino/libraries/RF24/RF24_config.h
Unescape View File

@ -0,0 +1,65 @@
/*
Copyright (C) 2011 J. Coliz <maniacbug@ymail.com>
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
version 2 as published by the Free Software Foundation.
*/
#ifndef __RF24_CONFIG_H__
#define __RF24_CONFIG_H__
//#if ARDUINO < 100
//#include <WProgram.h>
//#else
#include <Arduino.h>
//#endif
#include <stddef.h>
// Stuff that is normally provided by Arduino
#ifdef ARDUINO
#include <SPI.h>
#else
#include <stdint.h>
#include <stdio.h>
#include <string.h>
extern HardwareSPI SPI;
#define _BV(x) (1<<(x))
#endif
#undef SERIAL_DEBUG
#ifdef SERIAL_DEBUG
#define IF_SERIAL_DEBUG(x) ({x;})
#else
#define IF_SERIAL_DEBUG(x)
#endif
// Avoid spurious warnings
#if 1
#if ! defined( NATIVE ) && defined( ARDUINO )
#undef PROGMEM
#define PROGMEM __attribute__(( section(".progmem.data") ))
#undef PSTR
#define PSTR(s) (__extension__({static const char __c[] PROGMEM = (s); &__c[0];}))
#endif
#endif
// Progmem is Arduino-specific
#ifdef ARDUINO
#include <avr/pgmspace.h>
#define PRIPSTR "%S"
#else
typedef char const char;
typedef uint16_t prog_uint16_t;
#define PSTR(x) (x)
#define printf_P printf
#define strlen_P strlen
#define PROGMEM
#define pgm_read_word(p) (*(p))
#define PRIPSTR "%s"
#endif
#endif // __RF24_CONFIG_H__
// vim:ai:cin:sts=2 sw=2 ft=cpp

125
arduino/libraries/RF24/nRF24L01.h
Unescape View File

@ -0,0 +1,125 @@
/*
Copyright (c) 2007 Stefan Engelke <mbox@stefanengelke.de>
Permission is hereby granted, free of charge, to any person
obtaining a copy of this software and associated documentation
files (the "Software"), to deal in the Software without
restriction, including without limitation the rights to use, copy,
modify, merge, publish, distribute, sublicense, and/or sell copies
of the Software, and to permit persons to whom the Software is
furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be
included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
DEALINGS IN THE SOFTWARE.
*/
/* Memory Map */
#define CONFIG 0x00
#define EN_AA 0x01
#define EN_RXADDR 0x02
#define SETUP_AW 0x03
#define SETUP_RETR 0x04
#define RF_CH 0x05
#define RF_SETUP 0x06
#define STATUS 0x07
#define OBSERVE_TX 0x08
#define CD 0x09
#define RX_ADDR_P0 0x0A
#define RX_ADDR_P1 0x0B
#define RX_ADDR_P2 0x0C
#define RX_ADDR_P3 0x0D
#define RX_ADDR_P4 0x0E
#define RX_ADDR_P5 0x0F
#define TX_ADDR 0x10
#define RX_PW_P0 0x11
#define RX_PW_P1 0x12
#define RX_PW_P2 0x13
#define RX_PW_P3 0x14
#define RX_PW_P4 0x15
#define RX_PW_P5 0x16
#define FIFO_STATUS 0x17
#define DYNPD 0x1C
#define FEATURE 0x1D
/* Bit Mnemonics */
#define MASK_RX_DR 6
#define MASK_TX_DS 5
#define MASK_MAX_RT 4
#define EN_CRC 3
#define CRCO 2
#define PWR_UP 1
#define PRIM_RX 0
#define ENAA_P5 5
#define ENAA_P4 4
#define ENAA_P3 3
#define ENAA_P2 2
#define ENAA_P1 1
#define ENAA_P0 0
#define ERX_P5 5
#define ERX_P4 4
#define ERX_P3 3
#define ERX_P2 2
#define ERX_P1 1
#define ERX_P0 0
#define AW 0
#define ARD 4
#define ARC 0
#define PLL_LOCK 4
#define RF_DR 3
#define RF_PWR 6
#define RX_DR 6
#define TX_DS 5
#define MAX_RT 4
#define RX_P_NO 1
#define TX_FULL 0
#define PLOS_CNT 4
#define ARC_CNT 0
#define TX_REUSE 6
#define FIFO_FULL 5
#define TX_EMPTY 4
#define RX_FULL 1
#define RX_EMPTY 0
#define DPL_P5 5
#define DPL_P4 4
#define DPL_P3 3
#define DPL_P2 2
#define DPL_P1 1
#define DPL_P0 0
#define EN_DPL 2
#define EN_ACK_PAY 1
#define EN_DYN_ACK 0
/* Instruction Mnemonics */
#define R_REGISTER 0x00
#define W_REGISTER 0x20
#define REGISTER_MASK 0x1F
#define ACTIVATE 0x50
#define R_RX_PL_WID 0x60
#define R_RX_PAYLOAD 0x61
#define W_TX_PAYLOAD 0xA0
#define W_ACK_PAYLOAD 0xA8
#define FLUSH_TX 0xE1
#define FLUSH_RX 0xE2
#define REUSE_TX_PL 0xE3
#define NOP 0xFF
/* Non-P omissions */
#define LNA_HCURR 0
/* P model memory Map */
#define RPD 0x09
/* P model bit Mnemonics */
#define RF_DR_LOW 5
#define RF_DR_HIGH 3
#define RF_PWR_LOW 1
#define RF_PWR_HIGH 2
Write Preview
Loading…
Cancel
Save